NCU and QOS limits under SLURM

HiPerGator 2.0 documentation

Account and QOS Use

In the HiperGator 2.0 SLURM implementation a job's priority and resource limits are determined by its QOS (Quality of Service). Every group with an HPG2 investment will have a corresponding SLURM account. Each SLURM account has two associated QOSs - the normal or high-priority QOS and a low-priority burst QOS. In turn, each user who is a member of vested group has a SLURM association. It is the association which determines which QOSs are a available to a user. In addition to the primary group association, users who have secondary group membership (in the Unix/Linux sense) will also have secondary group associations which will afford them access to the normal and burst QOSs of that group's account.

To see your SLURM associations, you can run the showAssoc command. For example,

[root@slurm1 ~]# showAssoc magitz
              User    Account   Def Acct   Def QOS                                      QOS 
------------------ ---------- ---------- --------- ---------------------------------------- 
magitz                zoo6927      ufhpc     ufhpc zoo6927,zoo6927-b                        
magitz                  ufhpc      ufhpc     ufhpc ufhpc,ufhpc-b                            
magitz                 soltis      ufhpc    soltis soltis,soltis-b                          
magitz                  borum      ufhpc     borum borum,borum-b

The output above shows that the user magitz has four SLURM associations and thus, access to 8 different QOSs. By convention, a user's default account is always the account of their primary group. Additionally, their default QOS is the normal (high-priority) QOS of their default QOS. If a user does not explicitly request a specific account and QOS, the user's default account and QOS will be assigned to the job.

However, if the user magitz wanted to use the borum group's burst QOS (to which he has access by virture of the borum account association), he would specify the account as QOS in his batch script as follows.

    #SBATCH  --account=borum
    #SBATCH  --qos=borum-b

Note that both must be specified. Otherwise, SLURM will assume the default ufhpc account is intended and the borum-b QOS will not be available to the job. Consequently, SLURM would deny the submission.

These sbatch directives can also be given as command line arguments to "srun" as in,

    srun --account=borum --qos=borum-b some_command

QOS Limits

The second argument that determines job's priority and resource limits is '--qos'. There are two possible choices for QOS - the main investment QOS and the burst QOS formerly known as the 'soft' and 'hard' limit under Torque/MOAB. The QOS has to be explicitly specified as SLURM will not automatically move jobs between the two. The main qos has a 744-hour time limit and a high priority to make sure that a group can fully use its investment without having to wait for resources. To specify the main QOS use the group name in conjunction with the corresponding account. For example,

#SBATCH --account=mygroup
#SBATCH --qos=mygroup

The burst QOS has a 96-hour time limit and a lower priority as it depends on the availability of spare capacity on HiPerGator, but it provides the additional amount of 9x the resources of the main qos for a total of 10x of the investment between the two QOSes. To specify the burst QOS add '-b' to the group's name in the --qos argument. For example,

#SBATCH --account=mygroup
#SBATCH --qos=mygroup-b

There is another limit under SLURM, which applies to both QOS choices. A group can use all processor cores available to it under a particular qos only as long as it stays under the total memory limit for that QOS. The total memory limit is calculated as 'QOS NCU * 3gb'. For example, a main QOS of 30NCUs will have a group memory limit of 90gb while the burst qos for that group will be equal to '30 * 3gb * 9 = 810gb'. If the group memory limit is reached you will see a '(QOSGrpMemLimit)' status in the 'NODELIST(REASON)' column of the squeue output. For example,

squeue | grep MemLimit | head -n 1
           123456    bigmem test_job   jdoe PD       0:00      1 (QOSGrpMemLimit)

The above message can only be seen in the output of the 'squeue' command and does not interfere with job submission, but the job will stay queued until the group goes below its memory limit.

If the submitted job is so large that its resource request falls outside of the total resource limit within the requested QOS SLURM will refuse the job submission altogether and produce the following error

sbatch

error: Batch job submission failed: Job violates accounting/QOS policy (job submit limit, user's size and/or time limits)

Examples

A hypothetical group ($GROUP in the examples below) has an investment of 42 NCUs. That's the group's so-called soft limit for HiPerGator jobs in the main qos for up to 744 hours at high priority. The hard limit accessible through the so-called burst qos is +9 times that giving a group potentially a total of 10x the invested resources i.e. 420 NCUs with burst qos providing 378 NCUs of that capacity for up to 96 hours at low priority.

Let's test:

[marvin@gator ~]$ srun --mem=126gb --pty bash -i

srun: job 123456 queued and waiting for resources

<Looks good, let's terminate the request with Ctrl+C>

^C

srun: Job allocation 123456 has been revoked

srun: Force Terminated job 123456

On the other hand, going even 1gb over that limit results in the already encountered job limit error

[marvin@gator ~]$ srun --mem=127gb --pty bash -i

srun: error: Unable to allocate resources: Job violates accounting/QOS policy (job submit limit, user's size and/or time limits

At this point the group can try using the 'burst' QOS with

1. SBATCH --qos=$GROUP-b

Let's test:

[marvin@gator3 ~]$ srun -p bigmem --mem=400gb --time=96:00:00 --qos=$GROUP-b --pty bash -i

srun: job 123457 queued and waiting for resources

<Looks good, let's terminate with Ctrl+C>

^C

srun: Job allocation 123457 has been revoked

srun: Force Terminated job 123457

However, now there's the burst qos time limit to consider:

[marvin@gator ~]$ srun --mem=400gb --time=300:00:00 --pty bash -i

srun: error: Unable to allocate resources: Job violates accounting/QOS policy (job submit limit, user's size and/or time limits

Let's reduce the time limit to what burst qos supports and try again:

[marvin@gator ~]$ srun --mem=400gb --time=96:00:00 --pty bash -i

srun: job 123458 queued and waiting for resources

<Looks good, let's terminate with Ctrl+C>

^C

srun: Job allocation 123458 has been revoked

srun: Force Terminated job

Group Limit Errors

The following Reasons can be seen in the 'NODELIST(REASON)' column of the job queue listing for a group when the group reaches the resource limit for the respective account/qos combination:

QOSGrpCpuLimit

means that all CPU cores available for the listed account within the respective QOS are in use.

QOSGrpMemLimit

means that all memory available for the listed account within the respective QOS as described in the previous section is in use.